feat: display submergence factor in result messages

refs #520

src/locale/messages.en.json

@@ -2,11 +2,11 @@
     "ERROR_AT_LEAST_ONE_OF_THOSE_MUST_BE_DEFINED": "At least one of the following values should be specified : %variables%",
     "ERROR_CLOISON_AVAL_UN_OUVRAGE_REGULE": "Only one regulated device is allowed on the downstream wall",
     "WARNING_DEVER_ZR_SUP_Z1": "Elevation of the river bed can't be higher than water elevation: Impossible to calculate the kinetic energy",
-    "WARNING_DOWNSTREAM_ELEVATION_POSSIBLE_SUBMERSION": "Downstream elevation is higher than weir elevation (possible submersion)",
-    "WARNING_ORIFICE_FREE_DOWNSTREAM_ELEVATION_POSSIBLE_SUBMERSION": "Downstream elevation is higher than orifice center elevation (possible submersion)",
-    "WARNING_NOTCH_SUBMERSION_GREATER_THAN_07": "Notch formula is discouraged when submersion is greater than 0.7",
-    "WARNING_SLOT_SUBMERSION_NOT_BETWEEN_07_AND_09": "Slot formula is discouraged when submersion is lower than 0.7 or greater than 0.9",
-    "WARNING_WEIR_SUBMERSION_LOWER_THAN_08": "Submerged weir formula is discouraged when submersion is lower than 08",
+    "WARNING_DOWNSTREAM_ELEVATION_POSSIBLE_SUBMERSION": "Downstream elevation is higher than weir elevation (%submersionPerc%% submersion)",
+    "WARNING_ORIFICE_FREE_DOWNSTREAM_ELEVATION_POSSIBLE_SUBMERSION": "Downstream elevation is higher than orifice center elevation (%submersionPerc%% submersion)",
+    "WARNING_NOTCH_SUBMERSION_GREATER_THAN_07": "Notch submergence (%submersionPerc%%) is higher than recommended boundary (70%)",
+    "WARNING_SLOT_SUBMERSION_NOT_BETWEEN_07_AND_09": "Slot submergence (%submersionPerc%%) is not in the recommended boundaries (70 to 90%)",
+    "WARNING_WEIR_SUBMERSION_LOWER_THAN_08": "Weir submergence factor (%submersionPerc%%) is lower than the recommended boundary (80%)",
     "WARNING_INFO_COUNT_SHORT": "%d info(s)",
     "WARNING_WARNING_COUNT_SHORT": "%d warning(s)",
     "WARNING_ERROR_COUNT_SHORT": "%d error(s)",

src/locale/messages.fr.json

@@ -2,11 +2,11 @@
     "ERROR_AT_LEAST_ONE_OF_THOSE_MUST_BE_DEFINED": "Au moins une des valeurs suivantes doit être renseignée : %variables%",
     "ERROR_CLOISON_AVAL_UN_OUVRAGE_REGULE": "Un seul ouvrage régulé est autorisé sur la cloison aval",
     "WARNING_DEVER_ZR_SUP_Z1": "La cote du lit du cours d'eau ne peut pas être supérieure à la cote de l'eau : Impossible de calculer l'énergie cinétique",
-    "WARNING_DOWNSTREAM_ELEVATION_POSSIBLE_SUBMERSION": "La cote de l'eau aval est plus élevée que la cote du seuil (ennoiement possible)",
-    "WARNING_ORIFICE_FREE_DOWNSTREAM_ELEVATION_POSSIBLE_SUBMERSION": "La cote de l'eau aval est plus élevée que la cote du centre de l'orifice (ennoiement possible)",
-    "WARNING_NOTCH_SUBMERSION_GREATER_THAN_07": "La formule de l'échancrure n'est pas conseillée pour un ennoiement supérieur à 0.7",
-    "WARNING_SLOT_SUBMERSION_NOT_BETWEEN_07_AND_09": "La formule de la fente n'est pas conseillée pour un ennoiement inférieur à 0.7 et supérieur à 0.9",
-    "WARNING_WEIR_SUBMERSION_LOWER_THAN_08": "La formule du seuil noyé n'est pas conseillé pour un ennoiement inférieur à 0.8",
+    "WARNING_DOWNSTREAM_ELEVATION_POSSIBLE_SUBMERSION": "La cote de l'eau aval est plus élevée que la cote du seuil (ennoiement %submersionPerc% %)",
+    "WARNING_ORIFICE_FREE_DOWNSTREAM_ELEVATION_POSSIBLE_SUBMERSION": "La cote de l'eau aval est plus élevée que la cote du centre de l'orifice (ennoiement %submersionPerc% %)",
+    "WARNING_NOTCH_SUBMERSION_GREATER_THAN_07": "L'ennoiement de l'échancrure (%submersionPerc% %) est supérieur à la limite conseillée de 70 %",
+    "WARNING_SLOT_SUBMERSION_NOT_BETWEEN_07_AND_09": "L'ennoiement de la fente (%submersionPerc% %) ne se situe pas entre les valeurs limites conseillées de 70 à 90 %",
+    "WARNING_WEIR_SUBMERSION_LOWER_THAN_08": "L'ennoiement du seuil noyé (%submersionPerc% %) est inférieur à la limite conseillée de 80% ",
     "WARNING_INFO_COUNT_SHORT": "%d info(s)",
     "WARNING_WARNING_COUNT_SHORT": "%d avertissement(s)",
     "WARNING_ERROR_COUNT_SHORT": "%d erreur(s)",